Fixing a 3D Printer From the Shower
I don't know anything about 3D printing. My AI had never touched our new printer. By the end of the night it was running the machine, watching through its camera, and running tests while I was in the shower.
We got a Creality K1 Max. I tried to print a scraper that was already saved on it. It calibrated, it warmed up, it moved. Nothing came out. I don't know anything about 3D printing, so I handed it to JARVIS.
Step one: it read the machine before it guessed
JARVIS doesn't start with "have you tried turning it off and on". It connected to the printer's control port over the LAN and read its state directly: idle, no error code, nozzle and bed cold. Calibration and the self-test had passed, so motion was fine. That narrowed "no extrusion" down to three suspects: filament never reached the gears, a clog, or a nozzle sitting too close to the bed.
Step two: I was its hands
I stood at the printer with the Mini App camera open and talked. JARVIS watched the frames. I walked it around the back: spool, white tube, sensor box, blue tube, into the head. I found a lock knob, unlocked it, pushed the filament down until it stopped, and locked it. JARVIS told me the stop was normal (a cold nozzle is solid) and that the lock clamps the gears onto the filament.
Then I said "you heat it." It set the nozzle to 220, moved the head to the middle and pushed 50 mm. Plastic came out. It even dripped. First cause found: the filament had never been loaded into the extruder.
Step three: it lost its eye, and I called it on it
JARVIS started the print. Then it noticed its own camera had died, and I told it I wished it had fixed the camera first. Fair. It stopped the print (still at 0%), and went digging.
The firmware update I'd run earlier had quietly commented out the printer's camera stream. The camera was fine; the startup script just stopped launching the streamer. Even the printer's own web page showed a frowny face. JARVIS tried to speak the new WebRTC stream directly, got through codec mismatches and an SDP quirk, and hit a wall on the encryption handshake. Once root access was on (the printer shows you the login on its own screen), it found the commented-out line, started the stream by hand, and, with my OK, added a startup script so it survives reboots. It also cleared 47 old timelapse videos that weren't ours.
Its rule from tonight: check the eye before you start the job.
Step four: the shower
Second print. JARVIS checked its camera first this time, then started the job. Prep takes a few minutes, so the plan was to give it five and see if plastic hit the plate. I got in the shower.
From the shower I asked JARVIS to look through the camera. Layer 2 of 75, 3%, no errors... and it was printing air. The head was moving and nothing was coming out.
So we ran the extrusion test again. I suggested putting the nozzle close to the bed and then lowering the bed, so it could see any drip. It did exactly that: 220 Β°C, 5 mm above the plate, 50 mm of filament, then it moved the head aside and took a picture. Clean plate. Nothing.
It turned the heater off so nothing hot was left running with nobody at the machine, and told me what to look for when I'm out: unlock, pull the filament, read the end. A chewed notch means slipping gears, a blob means a clog, a clean break means it snapped inside.
What I noticed
- I didn't learn 3D printing tonight. I learned to be a good pair of hands.
- The useful moments were when JARVIS asked the machine instead of guessing, and when I pushed back.
- The best idea in the shower test was mine. It built the test around it and ran it without me in the room.
Still open: why extrusion stopped mid-print. To be continued once I'm dry.
P.S. This field note was also drafted, read back to me, edited, and posted from the shower. Haha.